Automationdirect.com DL06 Скачать руководство пользователя страница 47

Страница: 47 / 533

DL06 Micro PLC User Manual, 3rd Edition, Rev. E

Chapter 2: Installation, Wiring, and Specifications

3
4
5
6
7
8
9

10
11
12
13
14

2-4

Emergency Power Disconnect

A properly rated emergency power disconnect should be used to power the PLC controlled

system as a means of removing the power from the entire control system. It may be necessary

to install a capacitor across the disconnect to protect against a condition known as

outrush

This condition occurs when the output Triacs are turned off by powering off the disconnect,

thus causing the energy stored in the inductive loads to seek the shortest distance to ground,

which is often through the Triacs.
After an emergency shutdown or any other type of power interruption, there may be

requirements that must be met before the PLC control program can be restarted. For example,

there may be specific register values that must be established (or maintained from the state

prior to the shutdown) before operations can resume. In this case, you may want to use

retentive memory locations, or include constants in the control program to insure a known

starting point.

Orderly System Shutdown

Ideally, the first level of fault detection is the PLC control

program, which can identify machine problems. Certain

shutdown sequences should be performed. The types of

problems are usually things such as jammed parts, etc.,

that do not pose a risk of personal injury or equipment

damage

Class 1, Division 2 Approval

This equipment is suitable for use in Class 1, Zone 2, Division 2, groups A, B, C and D or

non-hazardous locations only.

WARNING: Explosion Hazard! Substitution of components may impair suitability for Class 1, Division 2.

WARNING: Explosion Hazard! Do not disconnect equipment unless power has been switched off or the

area is known to be non-hazardous.

WARNING: All models used with connector accessories must use R/C (ECBT2) mating plug for all

applicable models. All mating plugs shall have suitable ratings for device.

WARNING: This equipment is designed for use in Pollution Degree 2 environments (installed within an

enclosure rated at least IP54).

WARNING: Transient suppression must be provided to prevent the rated voltage from being exceeded

by 140%.

Jam

Detect

RST

Retract

Arm

Turn off

Saw

WARNING: The control program must not be the only form

of protection for any problems that may result in a risk of

personal injury or equipment damage.

Содержание DL06






















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DL06

Отзывы:

Похожие инструкции для DL06

Бренды по названию

Популярные бренды

Automationdirect.com DL06, Руководство пользователя

Результаты поиска

Содержание DL06

Отзывы:

Похожие инструкции для DL06

Бренды по названию

Популярные бренды