Austro Engine AE300-Wizard Скачать руководство пользователя страница 67

Страница: 67 / 89

AE300-Wizard

Document No.:

E4.08.09

AE_xx_000

Revision:

Page:

67 of 89

Dept.:

Electric/Electronic

Type:

User Guide

8.3.5

Live View – Working with Austro Engine Support

As indicated in section “11.1.4 Fourth Step (optional) – Live View recordings or Screenshots”

it might be required to use the Live View functionality to supply additional information when

working with Austro Engine “After Sales” support.

8.3.5.1

“LiveView-Config” Files

Configuration files may be sent to the local service center by the Austro Engine representa-

tive with the request to import it into the AE300-Wizard in order to collect data from special

measurements.

Steps:

1) A configuration file has been received by email or download
2) The “LiveView-Config” file is normally named similar to this example:

“

LiveView_Config_20101108 _OEVPI-RH_LP-Test.ae3

”

3) This file should be copied into the default Live View folder:

“

My Documents\Austro Engine\AE300-Wizard\LiveView

”

4) The configuration can then be imported into the AE300-Wizard as explained in chap-

ter “8.3.3 Live View – Online Analysis Using User-Defined Measurements” on page

63.

8.3.5.2

Live View Data saved during Measurements

Recordings saved during applicable Live View sessions can optionally be sent to Austro En-

gine “After Sales” support.

Steps:

1) Perform a Live View recording session and save the resulting data as explained in

chapter “8.3.1 Live View – Online Analysis and Recording”,

2) The default storage location for the recorded data is:

“

My Documents\Austro Engine\AE300-Wizard\LiveView

”,

3) The default name of the data file is for example: “

LiveView_20091123.ae3

”,

4) It is highly recommended to use additional descriptions for the file name like:

“

LiveView_YYYYMMDD_AircraftRegistration-EngineSide_ProblemShort.ae3

”,

5) Since version 1.2.0.xxx the AE300-Wizard stores all files (“Wizard files”) in a com-

pressed and encrypted format (“

.ae3

”) which reduces the size of Live View record-

ings dramatically (to about 1/10

of the previous format), and

6) Because of the smaller file size and the encryption used for privacy of the data, the

Live View recordings may be sent by email to the Austro Engine “After Sales” organi-

zation. Therefore FTP transfers are not required anymore and may be used as a

backup option or under special circumstances.

Содержание AE300-Wizard

























































































Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды

Austro Engine AE300-Wizard, Руководство пользователя

Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды