Austro Engine AE300-Wizard Скачать руководство пользователя страница 13

Страница: 13 / 89

AE300-Wizard

Document No.:

E4.08.09

AE_xx_000

Revision:

Page:

13 of 89

Dept.:

Electric/Electronic

Type:

User Guide

Limitations

WARNING

Using

the AE300-Wizard for measurements

during flight

not permitted!

The AE300-Wizard and its AE300-Dongle have the following limitations:



Use

only

in conjunction with the Austro Engine

AE300 series engine



Use

only

with an

Austro Engine EECU

(part number E4B-92-000-000).



Use

no other device

parallel to the AE300-Wizard to maintain the EECU firmware.



The AE300-Wizard is

only

available

in English

(The AE300-Wizard may be installed

on a system with a different system language, but the GUI will remain in English.

Although all system messages, i.e. file requesters, will be shown in the system lan-

guage.)

Содержание AE300-Wizard

























































































Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды

Austro Engine AE300-Wizard, Руководство пользователя

Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды