Austro Engine AE300-Wizard Скачать руководство пользователя страница 63

Страница: 63 / 89

AE300-Wizard

Document No.:

E4.08.09

AE_xx_000

Revision:

Page:

63 of 89

Dept.:

Electric/Electronic

Type:

User Guide

8.3.3

Live View – Online Analysis Using User-Defined Measurements

This Live View mode of operation is very similar to the previous “Pre-Defined Measurement”

chapter – but here a “LiveView-Config”, pre-defined by the user or another maintenance

support organization, is used to automatically set the mode of operation (standard/user),

sample-interval and set of signals.

Steps:

1)  Connect to ECU
2)  Select «Live View» tab
3)  Press  Load LiveView-Config

button

4) Select a file name
5) Click on Open

button

6) Up to 52 pre-defined signals per ECU, the required mode (standard/expert) and the

sample interval are set automatically

7) Press Record Live View button
8) … continue as explained in section “8.3.1.1 Live View – Standard Mode”

Содержание AE300-Wizard

























































































Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды

Austro Engine AE300-Wizard, Руководство пользователя

Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды