Austro Engine AE300-Wizard Скачать руководство пользователя страница 26

Страница: 26 / 89

AE300-Wizard

Document No.:

E4.08.09

AE_xx_000

Revision:

Page:

26 of 89

Dept.:

Electric/Electronic

Type:

User Guide

7.1.1.3

Live View Tab

Buttons to:

Load (import) a Live View file recorded previously ( Load Live View Recording )

Adjust the desired sample interval from 0.1s to 3s

Load (import) a user defined Live View configuration file ( Load LiveView-Config )

Save (export) a user defined Live View configuration file ( Save LiveView-Config )

Check/boxes to:

Switch from standard to expert mode to gain access to over 150 internal ECU-signals

Enable an auxiliary signal, which might be used on request by Austro Engine support

personal. It allows to select one ECU-internal signal per ECU which is not on the drop-

down list and has to be configured by its hex address.

Drop-down lists to:

Define a set of Live View signals to be recorded from each ECU (“ECU A/B Signals”)

Select one of 5 predefined measurements for display and recording of relevant Live View
signal sets:

○

“Boost-Pressure-Test”,

○

“PowerLever-Test”,

○

“Propeller Selftest”,

○

“Rail-Pressure-Test”, and

○

“Ca-Cr-Angle-Test”.

Содержание AE300-Wizard

























































































Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды

Austro Engine AE300-Wizard, Руководство пользователя

Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды