Austro Engine AE300-Wizard Скачать руководство пользователя страница 15

Страница: 15 / 89

AE300-Wizard

Document No.:

E4.08.09

AE_xx_000

Revision:

Page:

15 of 89

Dept.:

Electric/Electronic

Type:

User Guide

3.2

Hardware

3.2.1

Computer System

The requirements to the PC Hardware are:

Characteristic

Minimum

Recommended

PC System

Standard x86 desktop PC or laptop system

No. of CPU Cores

2 or more

Clock Frequency [GHz]

at least 2.8

RAM [GByte]

8 or more

HD Space (free)

[MByte]

100

for a full Wizard installation (including .NET Framework, VC++ redistrib-

utable library and HW drivers)

Additional HD Space

[MByte]

~100

(will be a good starting point) for log files and aircraft data

Table 3

Hardware Requirements

Note:

3 GByte RAM are required as a minimum space if no other program is concurrently

running! Otherwise more RAM is necessary.

Note 2:

It is recommended to use a Solid State Disk (SSD).

3.2.2

USB/CAN Adapter

A special USB/CAN adapter (provided with the AE300-Wizard) is required to physically con-

nect to the CAN bus of the EECU. It connects to a USB port (at least USB 2.0) of the PC sys-

tem on one end and provides a CAN bus male connector on the other. Additionally this

adapter also acts as a license dongle to enable the AE300-Wizard in one of two operating

modes defined by the license:

AE-order number “IPEH-002021-M CAN-USB Adapter M” to unlock “Maintenance mode”

AE-order number “IPEH-002021-QM CAN-USB Adapter QM” to unlock “Qualified mainte-

nance mode”

3.2.3

USB DataMatrix Scanner

A specially programmed DataMatrix scanner is optionally available from Austro Engine to

support scanning of IQA codes from injectors (see chapter “9.1.5 Scanning Injector IQA

Codes” on page 72). This is not a required item, but a recommended one to prevent mis-

reading of IQA codes:

Part#”

TBD

” hand held IQA scanner

3.2.4

CAN Extension Cable

It is recommended to use an RS-232 extension cable (female to male connectors) of about

2m (7ft) length for a convenient connection from the USB/CAN adapter of the PC/laptop to

the diagnostic plug in the aircraft cockpit.

Содержание AE300-Wizard

























































































Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды

Austro Engine AE300-Wizard, Руководство пользователя

Результаты поиска

Содержание AE300-Wizard

Отзывы:

Бренды по названию

Популярные бренды