50
Troubleshooting
PROBLEM
ACTION
Alenti
raises or lowers
after the hand control
button or the control
panel button is released.
1
Pull the battery out and remove the resident from
Alenti.
2
Remove the hand control and put the battery back. If the fail-
ure is gone, replace the hand control.
3
If the failure still occurs, contact qualified personnel.
Alenti
does not raise or
lower when the hand
control button or the
control panel button is
pressed.
1
Make sure the battery is connected correctly to
Alenti
.
2
Make sure the battery has sufficient charge, the battery
charger lamp located on
Alenti
turns green when the battery
is fully charged.
3
Make sure
Alenti
has not been lowered onto a fixed object.
If this occurs the automatic safety stop function will turn on.
4
Use the Emergency High/Low to remove resident from
Alenti.
Contact qualified personnel.
Alenti
functions only
operate with the use of
the control panel, not the
hand control.
1
Make sure that the hand control connection is properly con-
nected to the socket.
2
If the problem persists, replace the hand control.
Alenti
raises and stops
by itself.
1
Make sure that the safe working load of 182 kg (400lbs) is not
exceeded. The lowering function will still operate during this
scenario.
Alenti
is hard to
manoeuvre.
1
Make sure that the brakes are released.
2
Make sure that the castors roll and swivel freely. If not,
remove the resident from
Alenti
and contact qualified person-
nel.
If the brakes are not
functioning.
1
Make sure that
Alenti
is flat on a levelled surface
(floor surface must not exceed a slope ratio of 1:50).
2
If the brake alarm sounds, try moving the
Alenti
to a flat lev-
elled surface and re-apply brakes. If the alarm continues, con-
tact qualified personnel.
If the optional inte-
grated scale is not
operating.
1
Make sure the battery is connected correctly to
Alenti
.
2
Make sure the battery has sufficient charge. The battery
charger lamp located on
Alenti
turns green when the battery
is fully charged.
3
If the problem persists, contact qualified personnel.
The scale is showing
TILT.
1
Make sure
Alenti
is on a flat levelled surface.
2
If the problem persists, contact qualified personnel.
The scale is showing no
other error codes than
TILT.
1
Contact qualified personnel.
Содержание Alenti
