Arjo Huntleigh Sonicaid Team3 USA Скачать руководство пользователя страница 53

Страница: 53 / 84

Instructions For Use

11. Trouble Shooting

This section gives some of the more common problems encountered during use together with possible causes.

If the problem cannot be located after consulting the table in this section, the Team3 should be switched off,

disconnected from mains power source and a qualified technician should be consulted.

Before attempting trouble-shooting, verify that the power cable is properly connected to both the Team3 and

the mains power source.

11.1 Essential Performance

If you lose essential performance, refer to the table on page 98, Manufacturer's Performance Criteria

Specification.

11.2 FHR

SYMPTOM

POSSIBLE CAUSE / REMEDY

No FHR signal displayed

Check Team3 is switched on.
Check the FHR transducer is connected.

High % signal loss

Check transducer placement.
Check the transducer is not damaged.
Consider switching from Ultrasound to FECG.

No FHR trace printed

Check Print button has been pressed.
Check there is paper in the paper tray.
Check paper tray is fully pushed in.

Only one trace (twins) OR Traces

superimposed (twins)

Check ‘Printer Offsets’ in Printer setup. See Section 5.3.7

No beep when button pressed.

Check sound setting. See section 5.3.7.

Alarm not working

Alarm may be turned off. See Section 5.3.7

Team3 not printing/recording.

11.3 Fetal event marker

SYMPTOM

POSSIBLE CAUSE / REMEDY

No mark appears on the trace when the

mother presses the event marker.

Check event marker is connected
Check enough time has elapsed since button last pressed.

Team3 does not beep when the mother

presses the event marker

Check event marker is connected
Check sound setting. See section 5.3.7.

11.4 Maternal blood pressure

SYMPTOM

POSSIBLE CAUSE / REMEDY

No reading reported.

Check cuff and hose, then try another measurement.

Содержание Huntleigh Sonicaid Team3 USA





















































































Результаты поиска

Содержание Huntleigh Sonicaid Team3 USA

Отзывы:

Похожие инструкции для Huntleigh Sonicaid Team3 USA

Бренды по названию

Популярные бренды

Arjo Huntleigh Sonicaid Team3 USA, Инструкция по эксплуатации

Результаты поиска

Содержание Huntleigh Sonicaid Team3 USA

Отзывы:

Похожие инструкции для Huntleigh Sonicaid Team3 USA

Бренды по названию

Популярные бренды