Arjo Huntleigh Sonicaid Team3 USA Скачать руководство пользователя страница 54

Страница: 54 / 84

Instructions For Use

11.5 Printing

SYMPTOM

POSSIBLE CAUSE / REMEDY

Paper runs out

A colored stripe will appear when the paper pack nears its end (Sonicaid

paper). Once the paper has expired, the printer icon on the control bar will
change to

. Print information will be stored in memory for up to 100

hours to allow the paper pack to be changed.

Poor print quality

1. Make sure the correct paper is loaded.
2. Make sure the paper is loaded correctly.
3. Make sure the paper tray is fully pushed in.
4. Try printing again.
5. If there is no improvement, clean the print head. See Section 13.

Printer stops working

Check paper supply and feed. If not successful, swap unit out. Trace data is

stored in memory.

Содержание Huntleigh Sonicaid Team3 USA





















































































Результаты поиска

Содержание Huntleigh Sonicaid Team3 USA

Отзывы:

Похожие инструкции для Huntleigh Sonicaid Team3 USA

Бренды по названию

Популярные бренды

Arjo Huntleigh Sonicaid Team3 USA, Инструкция по эксплуатации

Результаты поиска

Содержание Huntleigh Sonicaid Team3 USA

Отзывы:

Похожие инструкции для Huntleigh Sonicaid Team3 USA

Бренды по названию

Популярные бренды