Arctic Cat Z Series 2006 страница 12 Скачать руководство пользователя

Страница: 12 / 88

GENERAL INFORMATION

CHARGING SYSTEM WARNING
LIGHT (660 cc Models)

The Charging System Warning

Light is designed to warn the opera-

tor if the battery charging system is

not functioning. The light should

illuminate each time the key is

turned to RUN or START, and it

should go out when the engine

starts. If the light stays illuminated

or it illuminates while the engine is

running, the battery is not being

charged, and the snowmobile is run-

ning on battery reserve power only.
If the Charging System Warning

Light illuminates, you should, as

soon as possible, take the snowmo-

bile to an authorized Arctic Cat

Snowmobile dealer for service. If

not under warranty, this service is at

the discretion and expense of the

snowmobile owner. The engine

WILL NOT RUN

without battery

power.

CHECK ENGINE LIGHT
(660 cc Models)

The Check Engine Light is con-

trolled by the ECU and may illumi-

nate for a number of reasons. The

light should illuminate each time the

key is turned to RUN or START, and

it should go out when the engine

starts. If the light stays illuminated

or it illuminates while the engine is

running, the ECU is receiving input

that is outside of its established

parameters. If the Check Engine

Light illuminates, take the snowmo-

bile to an authorized Arctic Cat

Snowmobile dealer for service. If

not under warranty, this service is at

the discretion and expense of the

snowmobile owner.

SPEEDOMETER/TACHOMETER

Some models are equipped with a

combination speedometer/tachome-

ter. Also incorporated into the

speedometer/tachometer are a digi-

tal readout screen and indicator

lights (battery, low oil, high beam,

check engine, and high tempera-

ture).



NOTE: The functions of the dig-

ital readout and indicator lights
will vary from model to model.

Top Button

By pushing the top button once

(lower right-hand side of the speed-

ometer/tachometer), the RPM and

MPH will be displayed (one on the

readout screen and one with the nee-

dle). By pushing the button once

again, the functions will be reversed.
By pushing the top button (with

speed being displayed) for more

than two seconds, the display will

show between standard mph or met-

ric kph. Release the button when

desired display appears.
By pushing and holding the top but-

ton, maximum RPM will be dis-

played on the readout screen. The

maximum RPM readout will reset

when the engine is shut off.

Bottom Button

By pushing the bottom button once,

the readout screen will display hour-

meter or trip-meter/odometer; by

pushing the button once again, the

two functions will be reversed. The

hour-meter readout will not reset.

Содержание Z Series 2006

























































































Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды

Arctic Cat Z Series 2006, Руководство оператора

Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды