Arctic Cat Z Series 2006 Скачать руководство пользователя | Manualshive

Страница: 87 / 88

background image

86

U.S. EPA EMISSION CONTROL STATEMENT/ WARRANTY COVERAGE

(U.S. Only)

STATEMENT/WARRANTY

Arctic Cat warrants to the original retail purchaser, and each subsequent purchaser, that all U.S. EPA-
certified Arctic Cat snowmobiles are designed, built, and equipped to conform to all U.S. EPA
Emission Control Regulations. Please read the following information completely.

Your authorized Arctic Cat snowmobile dealer will repair or replace any defective emission-related
component at no cost to you during the warranty period. You may have non-warranty service
performed by any repair establishment that uses equivalent components. The regulations provide
significant civil penalties for tampering that causes your snowmobile to no longer meet U.S. EPA
emission standards.

Arctic Cat further warrants that the engine and its emission-related components are free from defects
in materials or workmanship that could cause the engine to fail to comply with applicable regulations
during the warranty period.

If you have any questions about this information, or the emission warranty coverage statement,
contact your local authorized Arctic Cat snowmobile dealer.

WARRANTY PERIOD

The emission warranty period for this snowmobile begins on the same date as the standard warranty
coverage and continues for 30 months or 2500 miles, whichever comes first.

COMPONENTS COVERED

The emissions warranty covers major emissions control components and emission-related
components listed as follows:

Engine Management and Sensors

Barometric Pressure Sensor
Camshaft Position Sensor
Engine Control Unit (ECU)
Engine Coolant Temperature Sensor
Intake Air Temperature Sensor
Manifold Absolute Pressure Sensor
Oxygen Sensor
Throttle Position Sensor

Ignition System

Ignition Coil
Knock Sensor System
Spark Plugs
Capacitive Discharge Ignition (CDI) Module
Magneto Pick-Up

Fuel/Air System

Fuel Injectors
Fuel Pressure Regulator
Carburetor(s)
Turbocharger Assembly
Air Bypass Valve
Turbo Waste Gate Control Valve
Crankcase Ventilation System

Miscellaneous Items Used in
Aforementioned Systems

Connectors
Switches
Grommets
Clamps
Hoses
Ties
Gaskets
Wiring

OWNER'S RESPONSIBILITIES

The owner of any snowmobile warranted under this Arctic Cat Emission Control Statement is
responsible for the proper maintenance and use of the snowmobile as stated in the Operator's
Manual. Proper maintenance generally includes replacement and service, at the owner's choosing,
such items as air filer, oil and oil filter, or any other part, item, or device related to emissions control as
specified in the Operator's Manual. It is the owner's responsibility to ensure that the snowmobile is
used in a manner for which it was designed.

«
...
85
86
87
88
»

Содержание Z Series 2006

























































































Отзывы:

Нет отзывов

Похожие инструкции для Z Series 2006

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды