Arctic Cat Z Series 2006 Скачать руководство пользователя

Страница: 65 / 88

MAINTENANCE

2. Using the deflection tool/screw-

d r i v e r / s p a r k p l u g w r e n c h

assembly, remove the sheave

adjuster from the end of the

driven pulley.

3. Place the shim washers and O-

ring (as noted in removing)

onto the sheave adjuster; then

carefully thread the sheave

adjuster back into the driven

pulley. Tighten the adjuster

securely using the deflection

tool/screwdriver/spark plug

wrench assembly.



NOTE: Do not over-tighten the

sheave adjuster. A torque value of
2 . 1 k g - m ( 1 5 f t - l b ) i s r e c o m -
mended.

4. Close the belt guard; then

install the driven pulley plug.

5. Release the brake lever lock.

TRACK TENSION

Track tension is directly related to

the overall performance of the

snowmobile. If the track is too

loose, it may slap against the tunnel

causing wear or it may “ratchet” on

t h e t r a c k d r i v e s p r o c k e t s . I f

extremely loose, the idler wheels

may climb over the track lugs forc-

ing the track against the tunnel caus-

ing the track to “lock.” Arctic Cat

recommends that the track tension

be checked daily during the first 300

miles of operation and once a week

thereafter and adjusted according to

need. The track will stretch and take

a “set” during break-in. Track

deflection must be maintained

within the recommended range.

Checking Track Tension

1. Remove excess ice and snow

buildup from the track, track

drive sprockets, and the inside

of the skid frame.

2. Place the snowmobile up on a

shielded safety stand. Check to

make sure the track is 5-8 cm

(2-3 in.) off the floor.

3. At mid-point of the track (on

the bottom side), hook a spring

scale around a track clip; then

pull down on the scale to the

recommended pressure. Mea-

sure the deflection (distance)

between the bottom of the wear

strip and the inside surface of

the track clip. Compare the

measurement with the chart.



NOTE: On King Cat models and

M-Series models, no pressure
should be applied to the track.

! WARNING

Never operate the snowmobile
without the belt guard secured
in place.

! WARNING

Track tension must be properly
maintained. Personal injur y
could result if a track is allowed
to become excessively loose.

! WARNING

DO NOT attempt to check or
adjust track tension with engine
running. Turn ignition key to the
OFF position. Personal injury
could result from contact with a
rotating track.

Содержание Z Series 2006

























































































Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды

Arctic Cat Z Series 2006, Руководство оператора

Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды