Arctic Cat Z Series 2006 страница 22 Скачать руководство пользователя

Страница: 22 / 88

GENERAL INFORMATION

ADJUSTABLE BACKREST

The adjustable backrest is designed

for maximum comfort and safety.

When riding double, the backrest

must be adjusted to the most rear-

ward position. When riding single,

the backrest should be moved for-

ward to a position comfortable to the

operator. Be sure to maintain the

backrest pad in a vertical position in

all locations. Also, be sure to tighten

all retaining knobs securely after

adjusting the backrest.

0734-425

REMOVABLE REAR SEAT

Some snowmobiles are equipped

with a removable rear seat to allow

for additional cargo space when no

passenger is being carried. To

remove the rear seat, use the follow-

ing procedure:

1. Move and lock the adjustable

backrest in the forward posi-

tion.

2. Pull back on the seat latch han-

dle located at the bottom rear of

the seat.

3. Lift on the back of the seat and

move it rearward to remove it

from the tunnel.

0735-854

To install the rear seat, use the fol-

lowing procedure:

1. Place the seat into position on

the tunnel making sure the two

pins on the front of the rear seat

are properly engaged with the

receiving tabs on the rear of the

front seat.

2. Pull back on the seat latch han-

dle; then with the seat latch

handle pulled back, push the

rear seat forward and down and

release the seat latch handle.

! WARNING

Moving the backrest forward
limits the seating capacity to
one person only.

! CAUTION

On models equipped with a seat
warmer, disconnect the warmer
wiring harness prior to fully
removing the seat.

! WARNING

M a k e s u r e t h e r e a r s e a t i s
securely locked in place before
carrying a passenger or per-
sonal injury may result.

Содержание Z Series 2006

























































































Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды

Arctic Cat Z Series 2006, Руководство оператора

Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды