Arctic Cat Z Series 2006 страница 17 Скачать руководство пользователя

Страница: 17 / 88

GENERAL INFORMATION

DRIVE CLUTCH/DRIVEN
PULLEY ALIGNMENT

The parallelism and the offset

between the drive clutch and driven

pulley are set at the factory. Nor-

mally, no adjustment is necessary as

long as neither the drive clutch nor

the driven pulley is removed or dis-

assembled. However, if premature

drive belt wear is experienced or if

the drive belt turns over, the drive

clutch/driven pulley alignment must

be checked. Take the snowmobile to

an authorized Arctic Cat Snowmo-

bile dealer for this service. If not

under warranty, this service is at the

discretion and expense of the snow-

mobile owner.

DRIVE CHAIN TENSION
(Automatic System)

The drive chain must be properly

tensioned for proper operation to

prevent “ratcheting” and unneces-

sary chain/sprocket wear. The chain

tensioner in the drive system is auto-

matic; therefore, no adjustment is

required by the snowmobile owner/

operator. Arctic Cat recommends

that the chain, sprockets, and chain

tensioner be checked for wear and

the chain for proper tension every

year, 1000 miles, or whenever a

drive chain related problem is sus-

pected. Take the snowmobile to an

authorized Arctic Cat Snowmobile

dealer for this service. If not under

warranty, this service is at the dis-

cretion and expense of the snowmo-

bile owner.

DRIVE CHAIN TENSION
(Adjustable System)

The drive chain must be properly

tensioned for proper operation to

prevent “ratcheting” and unneces-

sary chain/sprocket wear. On these

snowmobiles, there are two different

chain tensioners in the chain case.

One chain tensioner is automatic

and one is manual. The automatic

chain tensioner will take up the slack

in the chain under most operating

conditions; however, every 500

miles or whenever repeated hard

accelerations will occur, the manual

chain tensioner should be adjusted.

Arctic Cat recommends that the

chain, sprockets, and chain tensioner

be checked for wear and proper

alignment and adjustment every

year, 1000 miles, or whenever a

drive chain related problem is sus-

pected. Take the snowmobile to an

authorized Arctic Cat Snowmobile

dealer for this service. If not under

warranty, this service is at the dis-

cretion and expense of the snowmo-

bile owner. To adjust the manual

drive chain tensioner, use the fol-

lowing procedure:

1. Loosen the jam nut on the chain

tensioner adjustment bolt.

2. Tighten the adjustment bolt fin-

ger-tight.

0730-323

! CAUTION

DO NOT attempt to service the
drive clutch and driven pulley.
The drive clutch and driven pul-
l ey mu s t b e s e r v i c e d by a n
authorized Arctic Cat Snowmo-
bile dealer only.

Содержание Z Series 2006

























































































Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды

Arctic Cat Z Series 2006, Руководство оператора

Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды