manualshive.com logo in svg

Arctic Cat Z Series 2006, Руководство оператора

Поделиться
Скачать
Arctic Cat Z Series 2006 Скачать руководство пользователя страница 20

GENERAL INFORMATION

19

TRACK STUDS

0726-207

Studs must be installed only on the

center belt using the pattern illus-

trated. For proper installation, use

the following procedure:

1. Measure 38 mm (1 1/2 in.) in

from the edge of the center belt;

then drill the stud hole using the

proper-sized hole drill.

2. Push the stud through the hole

from inside the track; then place

the domed support plate and

lock nut on the exposed stud.

3. Using a wrench to secure the

stud, tighten the lock nut on the

exposed stud.

It is also recommended that when-

ever studs are installed on a track,

c a r b i d e   w e a r   b a r s   s h o u l d   b e

installed on the skis. Carbide wear

bars complement the track studs to

balance steering control under these

conditions. The length of the carbide

on the wear bars should be propor-

tionate to the number of track studs

(i.e. small number of track studs —

short length of carbide...many track

studs — long length of carbide). The

proper proportion between the num-

ber of studs and carbide length on

the wear bar will maintain steering

balance.

 NOTE: Stud or hooker plate

installation will void track and
tunnel warranty.

! CAUTION

To protect the tunnel from pos-
sible damage from the studs, it
is recommended that Stud Pro-
tection Wear Strips be installed
o n   t h o s e   m o d e l s   n o t   s o
equipped.

! WARNING

Always balance the snowmo-
bile with the proper proportion
between the number of studs
and carbide length on the wear
bars. Do not “over drive” condi-
tions; use common sense in all
operating conditions.

! CAUTION

Do not use studs that are more
than 9.525 mm (0.375 in.) longer
than the track lug height. Also,
do not install studs in the outer
track belts.

! WARNING

Do not operate a snowmobile
with loose studs as they may be
thrown from the track. Always
use a shielded safety stand
whenever performing any main-
tenance or adjustments.

Содержание Z Series 2006

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды