Arctic Cat Z Series 2006 страница 40 Скачать руководство пользователя

Страница: 40 / 88

MAINTENANCE

The longevity and safety of the

snowmobile can be increased by

making periodic checks of the items

in the preceding checklist.
If, at any time, abnormal noises,

vibrations, or improper working

conditions of any component of this

snowmobile are detected, DO NOT

OPERATE THE SNOWMOBILE.

Take the snowmobile to an autho-

rized Arctic Cat Snowmobile dealer

for inspection and adjustment or

repair.
The snowmobile should be taken to

an authorized Arctic Cat Snowmo-

bile dealer at the end of each snow-

m o b i l i n g s e a s o n f o r g e n e r a l

inspection and for off-season stor-

age servicing. This inspection and

servicing is at the expense of the

snowmobile owner.

FUEL SYSTEM

In-Line Fuel Filter
(Carbureted Models)

Arctic Cat recommends that the in-

line fuel filter be checked weekly.

The in-line fuel filter is located just

in front of the fuel pump inlet fitting.

The filter must be clean to allow the

fuel hose to transmit the amount of

gasoline required. If the in-line fuel

filter is obstructed, gasoline flow

will be restricted; therefore, the filter

must be replaced. To remove and

install the in-line fuel filter, use the

following procedure:



NOTE: Determine which style

in-line fuel filter is being replaced
and remove and install accord-
ingly.

1. On models with a gas tank shut-

off valve, turn the gas tank shut-

off valve to the CLOSED posi-

tion.

2. Using a screwdriver, pry the

fuel hoses off the in-line fuel

filter and remove the filter.

726-065A

728-272B



NOTE: The in-line fuel filter

must be replaced if obstructed.
F i l t e rs a r e ava i l a bl e f ro m a n
authorized Arctic Cat Snowmo-
bile dealer.

3. Install the in-line fuel filter in

the fuel hose so the arrow on

the filter points toward the fuel

pump. Make sure the fuel hoses

fit tightly on the filter. If a fuel

hose does not fit tightly, cut 6

mm (1/4 in.) from the end of the

fuel hose; then install on the fil-

ter.

! WARNING

Whenever any maintenance or
inspection is made on the fuel
system in which there may be
fuel leakage, there should be no
welding, smoking, open flames,
etc., in the area.

Содержание Z Series 2006

























































































Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды

Arctic Cat Z Series 2006, Руководство оператора

Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды