Arctic Cat Z Series 2006 страница 78 Скачать руководство пользователя | Manualshive

Страница: 78 / 88

background image

MAINTENANCE

77

0727-726

AXIAL FAN BELT (370/440 cc
Models)

Arctic Cat recommends that the con-

dition of the axial fan belt be

inspected monthly.

1. Be sure ignition key is in the

OFF position.

2. Lift the hood and remove the

screws securing the fan cover;

then remove the fan cover.

3. Inspect axial fan belt for cracks,

wear, and proper tension.

726-155A

4. Using the thumb and forefinger,

check the tension (tightness) of

the fan belt by squeezing the

belt together near mid-span.

The maximum belt deflection

must not exceed 6 mm (1/4 in.).



NOTE: If the axial fan belt is

damaged or if the belt deflection
exceeds the specification, take
the snowmobile to an authorized
Arctic Cat Snowmobile dealer for
repair or adjustment. This service
is at the discretion and expense
of the snowmobile owner.

5. Install the fan cover.

ACCESSORY BELT (660 cc
Models)

Arctic Cat recommends that the con-

dition of the accessory belt be

inspected monthly.

Checking Belt Tension

1. Be sure ignition key is in the

OFF position.

2.

On the standard models,

remove the air cleaner assem-

b l y ; o n t h e t u r b o m o d e l s,

remove the intercooler assem-

bly.

3. Remove the bolts securing the

belt guard to the engine; then

remove the belt guard from the

engine compartment.

4. Inspect the belt for cracks,

wear, and proper tension.

! WARNING

DO NOT inspect the axial fan
belt while the engine is running.
Contact with the axial fan belt,
fan blades, or other moving
p a r t s m a y c a u s e p e r s o n a l
injury.

!WARNING

DO NOT inspect the belt while
the engine is running. Contact
with the belt, pulleys, or other
moving parts may cause per-
sonal injury.

«
...
76
77
78
79
80
...
»

Содержание Z Series 2006

























































































Отзывы:

Нет отзывов

Похожие инструкции для Z Series 2006

Бренд: Yamaha Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды