Arctic Cat Z Series 2006 Скачать руководство пользователя | Manualshive

Страница: 53 / 88

background image

52

MAINTENANCE

Removing/Installing Spark
Plugs (2-Stroke Models)

1. Remove the spark plug caps

from the plugs.

2. Using a spark plug wrench,

remove the plugs.

3. Install the plugs and finger-

tighten.

4. Tighten the spark plugs to 2.5-

2.8 kg-m (18-20 ft-lb); then

install the spark plug caps.

Removing/Installing Spark
Plugs (660 cc Models)

1. Remove the spark plug/coil

cover.

2. Remove the cap screws secur-

ing the spark plug coils to the

engine; then remove the coils.

3. Using a spark plug wrench,

remove the plugs.

4. Install the plugs and finger-

tighten.

5. Tighten the spark plugs to 2.1

kg-m (15 ft-lb); then install the

spark plug coils and secure

them with cap screws.

6. Install the spark plug/coil cover.

Checking Spark Plugs
(2-Stroke Models)

To see if the spark plugs being used

are of the proper heat range (after

the snowmobile has been operated

under normal driving conditions),

remove the spark plugs and exam-

ine the condition of the center elec-

trode insulator of each spark plug.

AO352A

A. TAN or LIGHT BROWN

insulator indicates correct

spark plugs (heat range).

B. LIGHT GRAY or WHITE

insulator indicates over-

heating of the engine. This

condition is caused by a too

lean condition or incorrect

spark plugs (heat range too

hot).

C. BLACK insulator indicates

fuel in the combustion

chamber is not burning

completely. This condition

is caused by a too rich

condition, too much oil, or

incorrect spark plugs (heat

range too cold).



NOTE: If the center electrode

insulators are light gray, white, or
black and if the carburetor adjust-
ments (on carbureted models),
oil-injection pump synchroniza-
tion, and ignition timing are cor-
rect, different heat-range spark
plugs may be necessary. Autho-
rized Arctic Cat Snowmobile deal-
e rs h av e d e t a i l e d sp a r k p l u g
information. Consult a dealer
before changing spark plugs, as
incorrect heat-range spark plugs
could cause poor engine perfor-
mance or engine damage.

«
...
51
52
53
54
55
...
»

Содержание Z Series 2006

























































































Отзывы:

Нет отзывов

Похожие инструкции для Z Series 2006

FS IQ TOURING 2008

Бренд: Polaris Страницы: 176

600 IQ Touring 2009

Бренд: Polaris Страницы: 165

Бренд: Polaris Страницы: 165

Бренд: Polaris Страницы: 212

MATRIX 650 INDY VR1 129

Бренд: Polaris Страницы: 243

Бренд: Polaris Страницы: 392

650 MATRYX INDY VR1 129 2021

Бренд: Polaris Страницы: 727

850 PRO-RMK 155 2.6" QD 2021

Бренд: Polaris Страницы: 747

Super Stinger 1975

Бренд: SCORPION Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды