Arctic Cat Z Series 2006 Скачать руководство пользователя

Страница: 23 / 88

GENERAL INFORMATION

REMOVABLE SEAT
(M-Series/King Cat/Sabercat
Models)

These snowmobiles are equipped

with a removable seat. To remove

the seat, use the following proce-

dure:

1. On the Sabercat, remove the

rear storage compartment.

2. On the bottom of the seat-base,

press the retaining clips away

from locking pins.

3. Lift on the back of the seat and

move it rearward to remove it

from the tunnel.

To install the seat, use the following

procedure:

1. Slide the front of the seat into

position on the tunnel; then

lower the rear of the seat onto

the locking pins.

2. Press down on the rear of the

seat until the retaining clips

snap into place on the locking

pins.

3. On the Sabercat, install the rear

storage compartment.

ARCTIC POWER VALVE
(APV) SYSTEM

This RPM controlled servomotor

(servo) actuated system adjusts the

size of the exhaust ports to provide

peak performance throughout the

RPM range. The system consists of

an exhaust valve assembly mounted

to the exhaust side of each cylinder

and connected by adjustable cables

to an electronic servo mounted

beneath the hood.



NOTE: The mounting location of

the servo will vary from model to
model.

739-152E

0739-152

At low RPM, the exhaust valves are

held in the DOWN position by

return springs. This gives the engine

a “low port” exhaust design cali-

brated to provide maximum low

RPM power and improve fuel econ-

omy at trail speeds.

739-152C

! WARNING

Make sure the seat is securely
locked in place or pers onal
injury may result.

Содержание Z Series 2006

























































































Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды

Arctic Cat Z Series 2006, Руководство оператора

Результаты поиска

Содержание Z Series 2006

Отзывы:

Похожие инструкции для Z Series 2006

Бренды по названию

Популярные бренды