manualshive.com logo in svg

Arctic Cat Z Series 2006, Руководство оператора

Поделиться
Скачать
Arctic Cat Z Series 2006 Скачать руководство пользователя страница 29

28

OPERATING INSTRUCTIONS

 NOTE: On EFI models when the

engine is being started, DO NOT
C O M P R E S S   T H E   T H R OT T L E
CONTROL LEVER. If the throttle
control lever is compressed, the
engine will not start because the
fuel/air mixture will be too lean.

7. On manual start models, pull

the recoil handle slowly until

resistance is felt; then give a

short quick pull. Repeat until

the engine starts.

 NOTE: On large-displacement

e n g i n e s   i n   e x t r e m e l y   c o l d
weather, pull the recoil handle
slowly two to three times to begin
the starting procedure.

 NOTE: On electric start models,

rotate the key to the START posi-
tion; then when the engine starts,
release the key.

8. On carbureted models when the

engine starts, allow it to warm

up for approximately 30 sec-

onds with the choke lever in the

full-choke position. After the

30-second warm-up, move the

choke lever to the middle posi-

tion. The choke lever should be

moved to the OFF position

when engine is warm. Slight

throttle control lever compres-

sion may be necessary after the

engine starts and during warm-

up. Idle the engine several min-

u t e s   u n t i l   t h e   e n g i n e   h a s

reached normal operating tem-

perature.

9. On EFI models when the engine

starts, allow it to warm up prop-

erly. Idle the engine several

minutes until the engine has

reached normal operating tem-

perature. Do not idle the engine

for excessively long periods of

time.

! CAUTION

To avoid damaging the recoil
starter, DO NOT pull the recoil
rope to its limit or release the
recoil handle from an extended
p o s i t i o n .   A l l ow   t h e   ro p e   t o
rewind slowly.

! CAUTION

Do not continuously run the
starter for more than 5 seconds
at a time.

! CAUTION

It is extremely important that the
engine is properly warmed up
before subjecting the engine to
high speed operation or heavy
loads. The engine should be
allowed to idle at least 3-4 min-
utes before it is operated at
m o r e   t h a n   1 / 2   t h r o t t l e .   I n
extremely cold conditions, the
warm-up time will be longer.
Cold seizure and piston scuffing
caused by insufficient warm-up
will not be covered by warranty.
Also, do not idle the engine for
excessively long periods of
time.

Содержание Z Series 2006

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды