APRILIA SL 750 SHIVER Скачать руководство пользователя

Страница: 111 / 303

•

If shorted to positive: excessive voltage has been detected at PIN 34 of the ENGINE con-

nector.

•

If shorted to negative: no voltage has been detected.

•

If the circuit is open: an interruption has been detected.

Troubleshooting

•

if shorted to positive: disconnect the injector connector, set key to ON, activate the compo-

nent with Axone and check the voltage on the filter casing grey/green cable on the filter

casing small connector towards the Marelli control unit: if there is voltage, restore the cable

harness between the filter casing connector and the Marelli control unit. If there is no voltage,

reconnect the connector and check if there is voltage at PIN -: if there is voltage, restore the

filter casing cable harness. If there is not, replace the sensor.

•

if shorted to negative: disconnect the injector connector, set the key to key ON and check if

there is a ground connection on the grey/red cable: if there is, restore the cable harness

between the filter casing connector and the Marelli control unit; if there is not, reconnect the

connector and disconnect the injector connector and check if there is a ground connection

on PIN -: if there is voltage, restore the filter casing cable harness. If there is not, replace

the injector.

•

the circuit is open: check the component correct electrical characteristic: if it is not correct,

replace the component; if it is correct, check the filter casing small connector, the connector

on the component and the Marelli control unit connector: If not OK, restore. If OK, check

cable continuity between the ENGINE PIN 34 and component PIN - and restore the cable

harness.

Coil

COIL

Function

Spark generation.

Operation / Operating principle

Inductive discharge system.

Level in wiring diagram:

coils and injectors.

Location:

•

on the vehicle: on the cylinder head

•

connector (if available): -

Electrical characteristics:

•

Primary circuit resistance: approx. 1

Ohm at 20°C between PIN 1 and 3.

SL 750 SHIVER

Electrical system

ELE SYS - 53

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции

Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды