APRILIA SL 750 SHIVER Скачать руководство пользователя страница 94

Страница: 94 / 303

With a released throttle grip, the value read should be 0%, whereas 100 % should be read with throttle

grip fully twisted.

AXONE: STATUSES

Throttle grip

Example value:

Slightly twisted_choked_fully twisted

Throttle grip autodetection

Example value:

carried out/not carried out

AXONE: PARAMETER ADJUSTMENT

Throttle grip autodetection

AXONE: ELECTRICAL ERRORS

Left side throttle grip position sensor track A P0150-

short circuit to positive / open circuit, short

circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 42 of the VEHICLE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 42 of the VEHICLE connector.

Troubleshooting

•

if shorted to positive: check the value shown by the parameter of the left Throttle Grip Po-

sition Sensor - track A: disconnect the left connector and see the value displayed by Axone:

if the voltage does not vary, there is a short circuit in the cable wiring; replace the throttle

grip sensor if the voltage drops to zero.

•

if the circuit is open, short circuit to negative: check the throttle grip sensor connector and

the Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between

the two cable terminals. If not OK, restore; if OK, check the cable earth insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not earth insulated,

restore the wiring. If it is earth insulated, and with the key set to ON, check that there is

power supply for the potentiometer PIN A and that PIN C is connected to earth. If both are

correct, replace the throttle grip sensor; if not, check the continuity of the cable that is not

functioning properly: if there is continuity, replace the control unit; if not, restore the wiring

Left side Throttle Grip Position sensor - track B P0151-

short circuit to positive / open circuit, short

circuit to negative

Error cause

•

Voltage that is excessive / equal to zero has been detected at PIN 40 of the VEHICLE

connector.

Troubleshooting

•

short circuit to positive: check the value shown by the parameter of the left Throttle Grip

position Sensor track B: disconnect the left connector and see the value displayed by Axone:

Electrical system

SL 750 SHIVER

ELE SYS - 36

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции, Страница: 94 / 303

Результаты поиска

Содержание SL 750 SHIVER

Отзывы: