APRILIA SL 750 SHIVER Скачать руководство пользователя

Страница: 130 / 303

not, it means that, with key set to ON, there is no 5V voltage at PIN 2: restore the cable harness whose

pink/white cable will be short circuit to ground

Air temperature sensor - instrument panel

INSTRUMENT PANEL AIR TEMPERATURE

SENSOR

Function

It tells the ambient air temperature to the instru-

ment panel.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Level in wiring diagram:

Temperature sensors

Location:

•

on the vehicle: on the plastic protection

under the instrument panel

•

connector: under the instrument panel

Electrical characteristics:

•

Resistance at 0°C: 32.5 kOhm +/- 5%

•

Resistance at 25°C: 10.0 kOhm +/- 5%

Pin-out:

1. Voltage 5V

2. Ground connection

AXONE: ELECTRICAL ERRORS

INSTRUMENT PANEL DSB 06

Error cause

•

The oil sensor failure is signalled when it is detected that the sensor circuit is open or short

circuit to positive.

Troubleshooting

•

Check the sensor connector and the instrument panel connector (PINS 10 and 30): If not

OK, restore; if OK, check the continuity of the pink cable between the sensor connector and

the instrument panel connector PIN 10: if not OK, restore the cable harness; if OK, check

the correct sensor resistance: if not OK, replace the sensor; if it is OK, check the continuity

of the yellow/black cable between the sensor connector and the instrument panel connector

PIN 30: If not OK, restore the cable harness; if OK, with key set to ON, check if there is

voltage at the sensor connector PIN 1: if there is no voltage, replace the instrument panel;

if there is approximately 12V, restore the cable harness (there is a short circuit in the battery).

Electrical system

SL 750 SHIVER

ELE SYS - 72

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции

Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды