APRILIA SL 750 SHIVER Скачать руководство пользователя

Страница: 184 / 303

Timing

•

Rotate the crankshaft until the front cylinder piston reaches the top dead centre.

•

Lock the crankshaft with the specific special tool

Specific tooling

020720Y Timing tool

If necessary, remove the timing system gears from

the camshafts:

•

Place the camshaft with the timing sys-

tem gear on a vice and protect the

cams of the camshaft adequately.

•

Unscrew and remove the nut.

ANTICLOCKWISE NUT FOR BOTH REAR CYL-
INDER SHAFTS, AN ANTICLOCKWISE AR-
ROW HAS BEEN PUNCHED ON IT.

•

Collect the washer.

•

Remove the timing system gear from

the camshaft.

•

Clean gears surfaces (camshaft cone and gear cone) with: "System MC 217 spray metal

cleaner".

•

Pre-fit the gear on the camshaft, so that it can turn freely.

•

Place the two camshafts in the head seats and align the two camshaft holes with the head

holes.

•

Align the clearance recovery gear to

the main timing system gear using the

specific tool.

Specific tooling

020718Y Camshaft gear alignment pin

Engine

SL 750 SHIVER

ENG - 36

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции

Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды