APRILIA SL 750 SHIVER Скачать руководство пользователя

Страница: 128 / 303

Side stand sensor

SIDE STAND SENSOR

Function

It tells the side stand position to the control unit.

Operation / Operating principle

If the gear is engaged and the side stand is unfol-

ded, and therefore the circuit is open, the control

unit does not enable vehicle start-up or shuts off

the engine if it is rotating.

Level in wiring diagram:

start-up enabling

switches

Location:

•

on the vehicle: on the side stand

•

connector: left side, near the Marelli

control unit

Electrical characteristics:

•

Side Stand Up: closed circuit (continu-

ity)

•

Side Stand Down: open circuit (infinite

resistance)

Pin-out:

1. Ground connection

2. Voltage 12V

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL CON-
CEPTS OF ELECTRICAL TROUBLESHOOTING FOUND AT THE BEGINNING OF THE CHECKS
AND CONTROLS SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: STATUSES

Side stand

Example value:

up/down

Indication on Axone

always down

: check the connector: if not OK, restore; if it is OK, disconnect the

two terminals from the sensor and check continuity to ground of PIN 1: if there is no continuity, restore

the cable harness; if there is, replace the sensor.

Indication on Axone

always up

: disconnect the terminals from the sensor and check if there is continuity

between the two PINS, with stand down: if there is continuity, replace the sensor; if the circuit is open,

it means that the brown/green cable from sensor PIN 2 to ENGINE connector PIN 6 is short circuit to

ground: restore the cable harness.

Electrical system

SL 750 SHIVER

ELE SYS - 70

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции

Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды