APRILIA SL 750 SHIVER Скачать руководство пользователя страница 177

Страница: 177 / 303

Checking the overhead camshaft

Check that the camshaft toothed wheel works

properly: if it is damaged or does not move

smoothly, replace both the timing chain and the

camshaft toothed wheel.

CAMSHAFT LOBES

•

Check that they do not show blue col-

ouring, pitting or scratches; otherwise,

replace the camshaft and the relevant

toothed wheel.

•

Use a micrometer to check the sizes

(a) and (b) of the camshaft lobes.

Camshaft lobes sizes:

Inlet

•

a: 36.28 / 36.32 mm (1.4283 / 1.4299

in); Limit: 36.15 mm (1.4232 in);

•

b: 28 mm (1.1023 in);

Outlet

•

a: 35.13 / 35.17 mm (1.3831 / 1.3846

in); Limit: 35.00 mm (1.3779 in);

•

b: 28 mm (1.1023 in);

•

Fasten the camshaft in horizontal po-

sition, as shown in the figure, and make

it spin to check the eccentricity with a

dial gauge; if necessary, replace the

component.

Camshaft eccentricity maximum limit 0.040

mm (0.0016 in)

Valve check

CAUTION

REPLACE THE VALVES ONE AT A TIME. DO NOT MIX THE COMPONENTS.
EACH VALVE MUST BE INSERTED IN ITS SEAT, MARKED BEFORE REMOVAL.

CAUTION

THE SEAT (1) ON THE VALVE HEAD CANNOT BE REGROUND. IF REQUIRED, REPLACE THE
VALVE.
GRINDING WITH ABRASIVE PASTE IS ALLOWED; VALVE STEM END REGRINDING IS NOT AL-
LOWED.

SL 750 SHIVER

Engine

ENG - 29

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции, Страница: 177 / 303

Результаты поиска

Содержание SL 750 SHIVER

Отзывы: