APRILIA SL 750 SHIVER Скачать руководство пользователя страница 83

Страница: 83 / 303

•

An oil sensor failure is signalled when it is detected that the sensor circuit is open or shorted

to positive.

DSB 07

- Oil pressure sensor

Error cause

An oil sensor failure is signalled when, with engine off, it is detected that the sensor circuit is open.

Troubleshooting

The test is performed only once when the key is set to ON. This error is signalled by the bulb icon, and

the general warning light turns on as well.

DSB 08

- Oil pressure sensor

Error cause

An oil sensor failure is signalled when, with engine running, it is detected that the sensor circuit is closed.

There is an error when the general warning light turns on.

Troubleshooting

This error is signalled by the bulb icon, and the general warning light turns on as well.

The instrument panel must keep all previous errors stored in its memory.

ERROR CLEARING

This option deletes all instrument panel errors; a further confirmation is requested. Use Axone to reset

ECU errors.

VEHICLE SERVICING RESET

This function is used to reset vehicle servicing. Using this function, the odometer can be reset only once

within the first 200 km (124 mi) of the vehicle, provided this has not been done by the Quality Check.

UPDATE

This function is used to program the instrument panel again. This screen page shows the software

version currently loaded; the LCD reads:

•

INSTRUMENT PANEL DISCONNECTED. NOW CONNECT THE DIAGNOSIS INSTRU-

MENT.

The instrument panel will restart to work normally after the key is inserted-extracted.

CHANGE KEYS

With this function the instrument panel can update the keys. Up to 4 keys can be stored.

The user code is first requested to be entered:

•

ENTER THE CODE

After entering the correct code, the following message should be shown on the display:

•

INSERT THE X KEY

•

INSERT THE X+1 KEY

At least one key must be programmed for the next start-ups. If no other key is inserted within 20 seconds

or if there is no power or after the fourth key is programmed, the procedure finishes and all the functions

of the vehicle and the instrument panel must be enabled (even if only one key has been programmed).

SL 750 SHIVER

Electrical system

ELE SYS - 25

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции, Страница: 83 / 303

Результаты поиска

Содержание SL 750 SHIVER

Отзывы: