APRILIA SL 750 SHIVER Скачать руководство пользователя

Страница: 196 / 303

•

Check that the axial clearance be-

tween the pin and the gear is between

0.30 and 0.60 mm (0.0118 - 0.0236 in).

•

Tighten the intermediate gear pin once

Loctite residues are thoroughly re-

moved and a high-strength threadlock

is applied on the thread.

•

Make sure that both timing chain slid-

ers are correctly fitted.

•

Refit the overhead camshafts following

the procedure described in the "Tim-

ing" section.

See also

Selecting the base gasket

Selecting the base gasket

•

Place the specific special tool on the

piston, which should have sealing rings

and be fitted on the connecting rod.

•

Lock the special tool with the clamp.

Specific tooling

AP8140302 tool for sealing ring fitting

•

Temporarily, fit the piston to the cylin-

der, without base or head gasket.

•

Remove the clamp from the sealing

ring locking tool.

•

Remove the special tool for locking the

connecting rod.

Engine

SL 750 SHIVER

ENG - 48

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции

Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды