APRILIA SL 750 SHIVER Скачать руководство пользователя

Страница: 281 / 303

•

Slide off the sleeve and empty the sys-

tem completely.

•

Refit both sleeves, place the corresponding clamps and tighten their screws.

•

Fill the expansion tank up to the marked level.

•

After bleeding the air from the tank, place the expansion tank cap.

•

Refit the front protection and tighten the screw.

•

Fit the right side fairing.

Water pump - overhaul

COVER REMOVAL

•

Drain off the cooling circuit completely.

•

Undo and remove the five screws.

•

Remove the water pump cover.

PUMP ROTOR REMOVAL

•

Remove the clutch-side cover.

•

Lock the pump shaft with a universal wrench on the hexagonal insert on the shaft.

•

Unscrew and remove the anticlock-

wise nut fixing the rotor.

•

Remove the rotor.

SL 750 SHIVER

Cooling system

COOL SYS - 5

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции

Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды