APRILIA SL 750 SHIVER Скачать руководство пользователя

Страница: 255 / 303

•

Replace both wheel bearings.

ALWAYS REPLACE BOTH BEARINGS.
ALWAYS REPLACE THE BEARINGS WITH OTHERS OF THE SAME TYPE.

•

Check the radial and axial clearance.

Axial clearance: a minimum axial clearance is allowed.

Radial clearance: none.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

REAR WHEEL GASKETS

•

Check that the gaskets are in good conditions; replace them if they show signs of damage

or excessive wear.

ALWAYS REPLACE BOTH GASKETS.
ALWAYS REPLACE THE GASKETS WITH OTHERS OF THE SAME TYPE.

REAR WHEEL PIN

•

Using a dial gauge, check the wheel

pin eccentricity (1). If the eccentricity

exceeds the limit value, replace the

wheel pin (1).

Characteristic

Maximum eccentricity:

0.25 mm (0.0098 in)

REAR WHEEL RIM

•

Using a dial gauge, check that the ra-

dial (A) and the axial eccentricity (B) of

the rim (2) do not exceed the limit val-

ue.

An excessive eccentricity is usually caused by

worn or damaged bearings. Replace the rim (2) if

after replacing the bearings, the value is not within

the specified limit.

Characteristic

Maximum radial and axial eccentricity:

2 mm (0.0079 in)

SL 750 SHIVER

Suspensions

SUSP - 25

Содержание SL 750 SHIVER
















































































































































































































































































































Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды

APRILIA SL 750 SHIVER, Руководство по обслуживанию станции

Результаты поиска

Содержание SL 750 SHIVER

Отзывы:

Похожие инструкции для SL 750 SHIVER

Бренды по названию

Популярные бренды