background image

2

WARNING: No helmet can protect the wearer from all 

foreseeable  high  or  low  speed  impacts.  However,  for 

maximum  protection,  the  helmet  must  be  of  proper  fit  and 

the chin strap must be securely fastened as described in this 

manual. Failure to have a proper fit and to securely fasten the 

chin strap is dangerous, as the helmet could come off in an 

accident, resulting in severe head injury or death.

CHOOSE YOUR SIZE

Each helmet is designed to correspond to a head measure-
ment (from for XS up to XL). To measure your head size, wrap 
a tape measure horizontally around your head at a height of 
approximately  one  inch  (2.5cm)  above  your  eyebrows. 
If  your  head  measurement  falls  between  two  sizes, 
first  try  on  the  smaller  helmet.  However,  because  of 
different  head  shapes,  this  size  reference  can  only  be 
considered as a guide. For maximum protection, it is neces-
sary to check that the helmet is well suited for the shape of 
your head.

When trying a brand new helmet, make sure that your head is 
pushed into the helmet as far as possible, with the front part 
just above your eyebrows, and with the chin strap securely 
fastened as described on the next page.

1

.

 

The  helmet  should  feel  very  snug  all  around  your  head 

and fairly tight on the cheek pads. If not, it is too big for you; 
select a smaller size. 

See figure A.

A

A

B

Summary of Contents for RSR2

























Reviews: