Applied Biosystems GeneAmp PCR System 9700 Скачать руководство пользователя страница 26

Страница: 26 / 132

2-4 Product Overview

Transfer or Storage

of Methods

You can transfer or store methods using a Methods Storage Card. The instrument can
run a method from its own software or from the methods stored on a Methods Storage
card.

Upgrading the

Firmware

There are two ways to upgrade the firmware:

♦

With a serial cable connection (PC communication cable P/N N805-1327 or
Macintosh communication cable P/N N805-1328) from the instrument’s
RS485 ports

♦

With a PCMCIA Flash Memory Card

Note

Upgrade firmware can be ordered from the Applied Biosystems web site or by

contacting PCR Technical Support.

For more information about upgrading the firmware, see the following.

Use...

To...

See...

Methods Storage Card,
Centennial 256kb SRAM
(P/N 0940-1064)

transfer methods from the
Methods Storage card to the
instrument or from the
instrument to the card for
storage.

“Copying Methods” on page
3-25.

If you are using...

See...

a serial cable connection (RS485 ports)

“Upgrading Through the Serial Port” on
page 3-19.

a PCMCIA Flash Memory Card

“Upgrading Firmware from a PCMCIA
Flash Memory Card” on page 3-23.

Microsoft Windows

95 or Windows NT

“Downloading Firmware Using
Windows 95 or Windows NT” on
page 3-21.

Windows

3.1

“Downloading Firmware Using Windows
3.1” on page 3-22.

Содержание GeneAmp PCR System 9700





































































































































Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды

Applied Biosystems GeneAmp PCR System 9700, Руководство пользователя

Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды