Applied Biosystems GeneAmp PCR System 9700 Скачать руководство пользователя страница 13

Страница: 13 / 132

Introduction and Safety 1-3

Instrument Safety

Before Operating the

Instrument

Ensure that everyone involved with the operation of the instrument has:

♦

Received instruction in general safety practices for laboratories

♦

Received instruction in specific safety practices for the instrument

♦

Read and understood all related MSDSs

Avoid using this instrument in a manner not specified by Applied Biosystems.

Although the instrument has been designed to protect the user, this protection can be impaired
if the instrument is used improperly.

Documentation User

Attention Words

Five user attention words appear in the text of all Applied Biosystems user
documentation. Each word implies a particular level of observation or action as
described below.

Note

Calls attention to useful information.

IMPORTANT

Indicates information that is necessary for proper instrument operation.

Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury. It may also be used to alert against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided, could result in

death or serious injury.

Indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury. This signal word is to be limited to the most extreme situations.

CAUTION

WARNING

DANGER

Содержание GeneAmp PCR System 9700





































































































































Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды

Applied Biosystems GeneAmp PCR System 9700, Руководство пользователя

Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды