Applied Biosystems GeneAmp PCR System 9700 Скачать руководство пользователя страница 108

Страница: 108 / 132

A-2 Instrument Specifications

System Specifications

Dimensions

The following tables list the footprint and the weight of the instrument with the 96–Well
or 60–Well sample block module.

Footprint (With Sample Block Module Installed)

Note

You must provide sufficient space around the instrument for unrestricted air circulation.

Weight

Note

See the sample block module user’s manual for physical information on a module.

Power

Configurations

There is one version of the instrument. The power requirements of the instrument
under various power configurations are:

Electrical

Requirements

IMPORTANT

You must be able to disconnect the main power supply to the instrument

immediately if necessary.

The following table specifies the electrical operating range for the instrument in various
parts of the world. Select appropriate fuse configuration based on the voltage used.

In Japan, the unit must have a dedicated 220-volt outlet! The unit will not

operate properly with a 100-volt outlet.

Note

The Volt-Amp number for this instrument is 725Volt Amps.

Height

26 cm (10 in)

Width

28 cm (11 in)

Depth

41 cm (16 in)

Base Module

8.6 kg (19 lbs)

96-Well Gold/Aluminum Sample Block Modules

3.2 kg (7 lbs)

VAC ~100/120

8 AMP T (5x20 mm) or

8 AMP Slow Blow (3 AB)

50/60 Hz

Use 250 V fuses

Max Power 725 VA

VAC ~220/230/240

8 AMP T (5x20 mm)

Location

Voltage (VAC)

a. Acceptable AC line voltage tolerances: 100, 120, 220, 230 ±10%; 240 VAC +6%/–10%, 50/60 Hz ± 1%.

Frequency

Amperage (A)

Nominal

Japan

220 ±10%

50/60 Hz ±1%

3.16

USA/Canada

120 ±10%

50/60 Hz ±1%

4.20

Europe (pre-1992)

220 ±10%

50/60 Hz ±1%

3.16

230 ±10%

50/60 Hz ±1%

3.14

UK (pre-1992)

240 +6%/–10%

50/60 Hz ±1%

3.12

Australia

240 +6%/–10%

50/60 Hz ±1%

3.12

WARNING

Содержание GeneAmp PCR System 9700





































































































































Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды

Applied Biosystems GeneAmp PCR System 9700, Руководство пользователя

Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды