Applied Biosystems GeneAmp PCR System 9700 Скачать руководство пользователя страница 109

Страница: 109 / 132

Instrument Specifications A-3

Control Panel Specifications

Display Screen

The display screen is a 7 x 40 character display with a graphics mode of 60 x 240 pixel
resolution.

Keys

The instrument control panel consists of a display screen and 22 keys. The keys are:

♦

Function keys

♦

Arrow keys

♦

Stop key

♦

Enter key

♦

10 number keypad

Sample Temperature Information

Temperature

The following table lists sample temperature information.

Note

Sample temperatures are displayed in degrees Celsius to the nearest 0.1 °C.

Printer Specifications

Serial Interface

Board Specifications

The instrument can use any printer with a serial (RS-232C) interface board with the
following parameters.

Cable Part Number

Connect the printer to the Instrument port with printer cable part number N805-1326.

Sample Temperature Range

4.0 to 99.9 °C.

Temperature Calibration

Traceable to National Institute of Standards and
Technology (NIST).

Baud Rate

9600

Parity

NONE

Data Bits

Stop Bits

Содержание GeneAmp PCR System 9700





































































































































Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды

Applied Biosystems GeneAmp PCR System 9700, Руководство пользователя

Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды