Applied Biosystems GeneAmp PCR System 9700 Скачать руководство пользователя страница 19

Страница: 19 / 132

Introduction and Safety 1-9

GeneAmp PCR System 9700 Labels and Warnings

Instrument Safety

Labels

Safety labels are located on the instrument. Each safety label has three parts:

♦

A signal word panel, which implies a particular level of observation or action (e.g.,

CAUTION

or WARNING). If a safety label encompasses multiple hazards, the

signal word corresponding to the greatest hazard is used.

♦

A message panel, which explains the hazard and any user action required.

♦

A safety alert symbol, which indicates a potential personal safety hazard.

Instrument

Warnings Diagram

The following diagram shows where the hazards and warnings labels are located on
the GeneAmp

PCR System 9700.

GR1069

Laboratory Use Electrical Equipment

3Z77

US LISTED

N2284

GeneAmp

PCR System 9700

Part No.

Serial No.

Made in Singapore

Warning

To reduce the chance of electrical shock
do not remove covers that require
tool access.
No user serviceable parts are inside.
Refer servicing to Applied Biosystems
qualified service personnel.

Warning

Grounding circuit continuity is vital
for safe operation of equipment.
Never operate equipment with
grounding conductor disconnected.

Foster City CA94404 USA

Warning

To avoid electrical shock,
disconnect power cord before servicing.

Fuse

100/120 VAC~

8 AMP T (5x 20MM) or

8 AMP SLOW BLOW (3 AB)

Fuses

220/230/240 VAC~

8 AMP T (5x 20 MM)

50/60 Hz

USE 250 V FUSES

MAX POWER 725 VA

Warning

For protection against fire hazard, replace
only with same type and rating of fuse.

Содержание GeneAmp PCR System 9700





































































































































Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды

Applied Biosystems GeneAmp PCR System 9700, Руководство пользователя

Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды