Applied Biosystems GeneAmp PCR System 9700 Скачать руководство пользователя страница 50

Страница: 50 / 132

3-22 Instrument Setup

Downloading

Firmware Using

Windows 3.1

To download the system firmware using Windows 3.1:

Step

Action

From the

Program Manager

, click the

Terminal

program icon.

From the

Settings

menu, choose

Communication

. A dialog box appears.

Enter the following information in the dialog box and click

From the

Binary Transfers

menu, choose

Settings

. A dialog box appears.

Select

Kermit

and click

From the

Send Binary File

menu, choose

Transfers

A directory dialog box appears.

From the directory dialog box, find and select the

9700 upgrade file

, and click

A message at the bottom of the window indicates that the program is sending the
file and a progress bar appears.

When the download is complete the GeneAmp PCR System 9700 automatically
resets.

When the download is complete, from the

File

menu, choose

Save

to save these

parameters.

In this field...

Enter...

Baud Rate

9600

Data Bits

Stop Bits

Parity

None

Flow Control

None

Connector

Com1 or Com2 (depending on the port to which the cable is
attached).

Содержание GeneAmp PCR System 9700





































































































































Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды

Applied Biosystems GeneAmp PCR System 9700, Руководство пользователя

Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Похожие инструкции для GeneAmp PCR System 9700

Бренды по названию

Популярные бренды