AMS EPIC SENSIT 3, Руководство по эксплуатации и обслуживанию

Страница: 16 / 52

L0190D
10
LED TRIM LIGHTING
Your new Epic vending machine is equipped with energy-
efficient LED lighted trim, and features several lighting schemes
to draw attention to the vendor. The lights for the dashboard and
coin cup openings are controlled by a circuit board, located on
the pull-out dashboard, below the control board.
Four push buttons on this PC board allow customization and
many options to increase customer appeal. Pressing the
color
button cycles through available solid colors. Pressing the
bright
button cycles through 3 levels of intensity. The
effect
and
speed
buttons can be used in combination to add movement to the
overall inviting look of the vendor.
DASHBOARD
Validator and Card Reader Locations
There are three locations that will accept bill validators and/or
card readers. The lower two positions meets the guidelines of
the 2010 Americans with Disabilities Act (ADA) for access by
handicapped persons. (See
MOUNTING AND CONNECTING
BILL VALIDATORS AND CARD READERS
on page 14.)
Coin Changer Location
Three screws are installed in the slide-out dashboard below the
coin chute. These screws mate to the keyhole slots on the back
of the changer. (See
MOUNTING AND CONNECTING COIN
CHANGER
on page 14.)
Coin Box
The coin box is located below the changer and is used to hold
non-payout denominations and overflow coins when the
changer’s payout tubes become full. It is removed by tilting
slightly and lifting out.
Door Switch
The door switch is mounted on the right side, near the coin box.
The control uses the door switch to change from service mode to
vend mode when the door is closed.
Display
The display is located on the front panel of the dashboard. It
serves as the interface for customers using and operators
programming the machine. In service mode, it displays the active
function and parameter values. In vend mode it can display the
selection entered, the price of a selected item and the credit
accumulated. When the machine is idle it can display the time
and a customizable scrolling message.
Keypad
The keypad is located below the display on the front of the
dashboard. A vending selection is made by keying in the number
combination that corresponds to the location of an item in the
machine. The keypad is also used to enter data in operation and
servicing of the vendor.
The actuator buttons include Braille characters to aid visually
impaired customers and operators.
Coin Return Button
The coin return button is located below the coin slot. Pressing
the coin return button will cause the Motorized Scavenge
Assembly to depress the coin return lever on the coin mech to
release bent or irregular coins that are not accepted by the
changer. While the scavenge cycle is active, the button will light
up to signify that it is in operation.
If the machine fails to vend a selection that has been made,
pressing the coin return will return the full credit. If the Force
Vend option is disabled, it can also return the full credit before a
selection is made. If the Bill Changer option is enabled, the coin
return will return bills held in escrow and/or change for bills
inserted and stacked in the bill validator.
Motorized Scavenge Assembly
This assembly operates the coin return lever of your coin mech
to mechanically release coins that cannot pass through the mech
or to initiate a vend cancellation and cause the return of monies
inserted. A small circuit board drives a motor (the same motor
used on the product trays) through a single revolution which
causes a cam to depress the lever on the mech. See also
Figure 4.1.
TRAY RAILS
The rails are located inside the cabinet and are used to support
the trays. The rails are adjustable up and down in 1/2”
increments. (See
TRAY VERTICAL POSITIONS
on page 17.)
TRAYS
See
TRAY ADJUSTMENT AND CONFIGURATION
on page 17,
and
OPTIONAL EQUIPMENT
on page 43 for optional tray
accessories.
3 VENDOR SYSTEMS AND COMPONENTS
Figure. 3.3 Motorized Scavenge Assembly
Figure. 3.2 LED Control Board