AMS EPIC SENSIT 3 Скачать руководство пользователя | Manualshive

Страница: 30 / 52

background image

L0190D

24

Sensit
This

setting ignores the Motor’s home switch (if present)

completely. When the product is detected the motor is
stopped and the vend cycle is complete.

Home/
This

is similar to HomeSensor/, except that if no drop is

detected the motor will make 2 short jogs in an effort to
dislodge the product. If the motor stops

off

the home

position, the next vend will begin the process again: it
will stop at home and if a drop is detected the vend
cycle is complete. If not, try up to two jogs. This is
similar to the original Sensit sequence, and is the factory
default setting for all vendors.

Home_Only/
This setting

disregards the Sensit system, and will make one

complete turn and take credit- whether a drop is detected or not.

Auto Sensor Recovery is an improvement to the AMS Sensit
system, that allows certain vends even when the sensor system
is blocked or malfunctioning. If Motor Type is set to Home/
Sensor/3 or Home /3, and the sensor system is

inoperable, the control will automatically switch to Home_Only/3
and allow a vend. Simply put, the sensors will be ignored, the
helix will make a full turn and the credit value will be deducted.
Once the error is cleared, the vendor will return to its original
sensor setting.

Note

that this will only work with the 23007 and

23007-01 motors, and during this temporary mode, selecting an
item with the older style motor will read “selection unavailable”.

4. Delayed Stop

The user can program a delayed stop of up to one second to
allow a motor to continue running after the product has been
dispensed.

Note:

this feature will only work with the

1-Sensit

motor setting.

ENTER

SELECTION

– Enter the number of the

selection to be delayed, enter

9

to edit, then enter the

time in tenths of a second. The decimal point is placed
automatically.

Example: Entering

8

will program a delay

of 0.8 seconds.

MOTOR TYPES

ITEM

DISPLAYED OPTION

MOTOR STOP

CREDIT DEDUCTION

1

SENSIT

Sensor*

Sensor

2

HOME/SENSOR/3

Home

Sensor

3

HOME//3

(FACTORY DEFAULT)

Home + Extra**

Sensor

4

HOME_ONLY/3

Home

Home

(S2 WITH HOMING) MOTOR TYPES

5***

HOME/SENSOR/2

Sensor

Sensor

6***

HOME//2

Home + Extra**

Sensor

7***

HOME_ONLY/2

Home

Home

* If S3 motors are used: the switch function is ignored, and homing & coupling are not available.

** "Extra" means that if a drop is not detected by the home position, the motor will move 2 additional

increments to try to vend the product.

*** These are settings for use only with vendors equipped with Sensit 2 with Homing.

6

SERVICE

PROGRAMMING

«
...
28
29
30
31
32
...
»

Содержание EPIC SENSIT 3





















































Отзывы:

Нет отзывов

Похожие инструкции для EPIC SENSIT 3

Бренд: Samsung Страницы: 48

Бренд: Kangaroo Страницы: 36

Бренд: Singer Страницы: 12

Бренд: Olivetti Страницы: 72

Бренд: Tesco Страницы: 36

Бренд: Janome Страницы: 38

Бренд: Philips Страницы: 54

Бренд: Philips Страницы: 59

Бренд: Philips Страницы: 2

MAGIC 5 ECO PPF 631

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 24

Бренд: Philips Страницы: 100

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 84

Бренд: Panasonic Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды