AMS EPIC SENSIT 3, Руководство по эксплуатации и обслуживанию

Страница: 23 / 52

L0190D
17
5
TRAY ADJUSTMENT AND CONFIGURATION
The trays in AMS Sensit 3 vendors are highly configurable.
Practically any combination of wide and narrow columns can be
set up on a tray. Before changing the configuration of your trays,
make sure to order the parts you will need, such as new helices,
dividers or additional motors.
SNACK AND CANDY TRAY
Removal
1. To remove the tray, start with the tray pushed to its
rearmost position. Lift the back of the tray up and
pull the tray forward about ten inches. Reposition
your hands to grasp the tray at its sides and slide
the tray out. If the tray is spaced close to the tray
above, it may be helpful to raise the front of the
tray as you pull it free.
2. When removing a tray, it is not necessary to
disconnect the tray harness. The harness is long
enough that it will allow a removed tray to be
placed on the floor without having to be
disconnected.
Installation
To install the tray, place the tray on top of the rails and
slide the tray all the way to the rear. It will automatically
drop into position. Make sure the harness slack is
draped over the outside of the rail.
TRAY VERTICAL POSITIONS
The trays can be adjusted to different vertical positions in 1/2
inch increments. To reposition a tray use the following steps.
Removal
1. Remove the tray for access to the support rails.
2. Remove the screw located at the front of each rail.
3. The front of the rail can now be lifted upward and
disengaged from the vertical column.
4. Pull forward to disengage the rail from the slots at
the back of the cabinet.
5. Use these same steps for the other side.
Installation
1. To reinstall the rail in the new position, locate the
rear “T” slots that will be used.
2. Then push the two tabs at the back of the rail into
the appropriate slots.
3. Engage the hooked tabs at the front of the rail into
the appropriate rectangular holes and pull down.
4. Make sure the rail is level.
5. Replace the screw to prevent the trays slipping out.
6. Use these same steps for the other side.
7. Reinstall the tray, making sure the harness is
routed over the top of the rail and all slack is
draped to the outside of the rail.
TRAY COLUMN POSITIONS
The tray columns used for snacks and candy can be configured
by the user for up to 10 columns wide (for 39” cabinets) trays.
Typically the vend columns are set to single (2.66”) or double
(5.32”) width, to be used with the standard small or large helices,
respectively. Single and double width columns can be
configured in any arrangement on the tray by following the
procedure below.
Plan your tray arrangement before beginning to determine which
extra parts may be required. Contact your distributor to order the
necessary parts.
1. Disconnect the harness and remove the tray. Place
the tray on a flat, stable work surface.
2. Reposition, remove, or add tray dividers in the
desired locations. To remove the divider, push
rearward then lift. Reverse the procedure to
reinstall.
3. It may be necessary to remove a motor and helix in
order to install some dividers. Pull forward on the
helix to remove it from the motor. Press down and
rearward on the top motor tab to remove the motor
from the tray.
4. Reposition the motors to the center of each vend
column, using the upper mounting position for the
large helix and the lower position for the small
helix. It may be easiest to disconnect the motors
from the harness first.
5. The harness has 10 sets of motor connections.
The first set of connections (at the end of the
harness farthest away from the connector) is
position 0, followed by 1, 2, 3, and so on. The last
set (nearest to the wire connector) is position 8
(35” cabinets) or 10 (39” cabinets). Starting at the
left side of the tray, attach the harness connectors
to the motors in order. For double columns, use the
even numbered connection and disregard the odd
numbered connection. (Example: If the first column
on the left is double width, disregard position 1 and
attach the connectors for position 0). Each set of
connectors has a wide and a narrow connector,
corresponding to a wide and a narrow tab on the
back of the motor. (See table of
Tray Motor Wire
Colors
on page 18.)
6. Place the correct Selection ID label in front of each
column, according to the motor connections used.
7. Replace the tray in the machine, routing the
harness over the tray rail and through the back of
the column.
8. Reconnect the harness, routing it over the rail and
through the back of the column.
9. Reinstall the tray.
10. After changing the tray configuration, it will be
necessary to reconfigure the motor matrix (See
VENDOR PREPARATION and INSTALLATION
on page 13.)