manualshive.com logo in svg

AMS EPIC SENSIT 3, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
AMS EPIC SENSIT 3 Скачать руководство пользователя страница 37

L0190D

 

 

31

 

7

 

TROUBLESHOOTING

 

ERROR CODES – CAUSES AND SOLUTIONS

 

TOP LEVEL 

ERROR CODE

 

SUB LEVEL 

CODE

 

CAUSES

 

SOLUTIONS

 

X STUCK

 

NONE

 

Keypad selection button X has been 

depressed more than 2 minutes.

 

Clear any obstructions or dirt from around the 

selection buttons and make sure they can move 

freely. If proper operation is not restored, replace the 

keypad.

 

SENSIT 

BLOCKED

 

NONE

 

The vend sensor is blocked 

or lens is fogged.

 

Remove any obstructions from the path of the 

sensor.

 

SENSIT 

DISCONNECTED

 

NONE

 

The vend sensor is disconnected.

 

Check all sensor harness connections.

 

HOME ERROR

 

NONE

 

Motor switch problem.

 

Check for correct motor type. Check for proper 

connections. Check for correct motor set-up. 

See 

TRAY SETUP 

on page 23.

 

MOTOR 

JAMMED

 

XX JAMMED 

The indicated motor (‘XX’) drew 

excessive current

 

Caution! See 

CLEARING JAMMED 

MOTOR 

ON Page 32.

 

CHANGER 

A message has been generated by the changer. 
Press 

1

 to see changer sub-level error codes. 

COMM 

COMMUNICATIONS – 

Communications error. 

Check MDB harness connections. 

SENSOR 

SENSOR – Sensor error. 

Consult changer manual or manufacturer. 

JAM TUBE 

JAMMED TUBE – Jammed coin tube.  Clear any obstructions from the coin tube. 

CHK SUM 

CHECK SUM – Check sum error. 

Consult changer manual or manufacturer. 

CHUTE 

CHUTE – No coins accepted for a 

period of time. 

Clear any obstructions from the coin chute. 

BILL 

VALIDATOR 

A message has been generated by the bill validator. 
Press 

1

 for bill validator sub-level error codes. 

COMM 

COMMUNICATIONS – 

Communications error. 

Check MDB harness connections. 

STK FULL 

STACKER FULL – Stacker is full. 

Empty stacker. 

MOTOR 

MOTOR – Bad stacker motor. 

Consult acceptor manual or manufacturer for repair. 

JAM BILL 

JAMMED BILL -  Bill is jammed. 

Clear any jammed bills from the acceptor. 

CHK SUM 

CHECK SUM – Check sum error. 

Consult acceptor manual or manufacturer. 

SENSOR 

SENSOR – Sensor error. 

Consult acceptor manual or manufacturer. 

CARD READER 

A message has been generated by the card reader. 
Press 

1

 to see sub-level error codes. 

CARD ERROR –. 

Card error. 

Use a different card. 

INVALID CARD – 

Invalid card. 

Use a different card. 

TAMPER 

Tamper error. 

Consult card reader manufacturer’s manual. 

COMM Communications 

error. 

Check MDB harness connections. 

SERVICE 

Unit needs service. 

Consult card reader manufacturer’s manual. 

READ ERROR 

Reader failure. 

Consult card reader manufacturer’s manual. 

JAMMED CARD 

Card is jammed. 

Clear the jammed card from the card reader. 

Содержание EPIC SENSIT 3





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды