AMS EPIC SENSIT 3 Скачать руководство пользователя | Manualshive

Страница: 49 / 52

background image

L0190D

43

11

OPTIONAL

EQUIPMENT

Part No. 20449 - Kit, Candy Pusher

The candy pusher is an adjustable bar that mounts to any tray
divider to keep tall candies from falling sideways. Four of these
are provided with the standard glass front vendor.

Part No. 20450 - Kit, Helix Splitter

The helix splitter is a plastic divider that can be inserted into a
small helix to divide each coil into two product openings, thereby
doubling product capacity. The helix splitter works best with
narrow products such as Life Savers.

Part No. 20535 - Kit, Cup Rail, Small Helix

Part No. 20536 - Kit, Cup Rail, 4” Helix

Part No. 20723 - Kit, Cup Rail, 3” Helix

The cup rail is a flat plastic bar that can be placed inside the
helix to provide a flat surface for rigid flat-bottomed packages
that otherwise do not stay upright when placed in a helix.
Examples would be drink boxes, small bottles, or individual
serving cups of soup, pudding, etc.

P/N 20786, Harness, Chip Programming

Use with the speech hardware and software program.

P/N 3701, S3 Utility Programming software

Use with 20786 harness.

Part No. 24056 – Kit, 39” High capacity Heavy product tray.

Based on a reinforced snack tray, allows vending 10 columns of
cans.

Part No. 24057 – Kit, 39” High capacity Heavy product tray,
with scrolling prices.

Based on a reinforced snack tray, allows vending 10 columns of
cans.

Part No. 24046 - Kit, Mini Dispenser

Replaces a snack selection with 1.5” helix and spacer.

Part No. 24012-x - Kit, Scrolling price conversion

Convert any tray to new scrolling prices. Specify tray type when
calling the factory.

Part No. 25722—K-Cup Kit

Installation of K-Cup rail assembly to a snack tray assembly.

«
...
47
48
49
50
51
...
»

Содержание EPIC SENSIT 3





















































Отзывы:

Нет отзывов

Похожие инструкции для EPIC SENSIT 3

Бренд: Panasonic Страницы: 2

Бренд: Fellowes Страницы: 4

Бренд: Fellowes Страницы: 4

Бренд: IGEBA Страницы: 59

Бренд: IGEBA Страницы: 48

Бренд: Oki Страницы: 28

Бренд: Sagem Страницы: 44

CoverPro 1000CP

Бренд: Janome Страницы: 21

Бренд: Count Страницы: 27

Бренд: Pfaff Страницы: 130

Бренд: JUKI Страницы: 4

796.3155 series

Бренд: Kenmore Страницы: 34

Бренд: ZOJE Страницы: 26

Бренд: Radio Shack Страницы: 20

Бренд: Radio Shack Страницы: 24

Бренд: Atlanta Attachment Company Страницы: 44

Бренд: Atlanta Attachment Company Страницы: 44

Бренд: Atlanta Attachment Company Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды