Ametek OCS 500 M6 Скачать руководство пользователя страница 54

Страница: 54 / 80

AMETEK CTS

OCS 500 N6 series

Manual for Operation

V 5.24

54 / 80

8.1.2.2.

Manual test routine

The manual test menu is only in the single phase equipment available.

Within this test routine all standard parameters can be easy set. A test cycle makes

10 impulses

within this

setting.

Manual standard test routine

Damped Osc. 1MHz IEC 61000-4-12

<- ->

Level 3

2000V 12 Ohm 0 dgr L-N

Testtime 0:00:45 h

Start

/- oV/A Imp L--PE N-PE L+N-PE Common mode menu

Start

/- oU/A Imp L--N /

Differential mode menu

Example:

- By pushing the cursor

➔

the test level will be increased/decreased to the next standard level.

- By turning the Inc. knob the test voltage V resp. the phase angle A will be adjusted continuously. The blinking

circle (

) shows which parameter can be changed.

Pressing the function „O V/A“ will change between both

parameters.

- Pressing the function keys the related function will be immediately activated.

- The displayed time will be resettled to zero after every new setting.

It is allowed to change all parameters during a running test

Содержание OCS 500 M6

















































































Результаты поиска

Содержание OCS 500 M6

Отзывы:

Ametek OCS 500 M6, Руководство по эксплуатации, Страница: 54 / 80

Результаты поиска

Содержание OCS 500 M6

Отзывы: