Ametek OCS 500 M6 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 80

Ametek OCS 500 M6 Скачать руководство пользователя страница 15

AMETEK CTS

OCS 500 N6 series

Manual for Operation

V 5.24

15 / 80

9

External trigger

10

Power on switch and fuse

11

Mains selector 115V / 230V

12

Fuse of the high voltage power supply

13

Parallel interface IEEE

14

Optical interface (USB)

15

Remote control connector

16

FAIL 1 / FAIL 2 connector

9

External trigger (BNC plug)

Trigger input for a pulse release. Trigger level 5-15V positive going.

10 Power on switch

The switch is part of the mains filter. Mains fuses are part of the filter. (230V / 1A and 115V / 2A)

11 Mains selector

Selection of 115V / 230V

12 Fuse of the high voltage power supply

The high voltage power supply is protected by this fuse „F3“. In case that no high voltage is generated but the
control unit works properly this fuse shall be checked.

13 Parallel interface GPIB / IEEE 488

IEEE 488 interface with IEEE connector

14 Optical interface (USB)

For data transfer an optical USB interface is available. The user must set the same Baud rate in the device and
control software. (Default setting 9600 baud).
When the interface is not used, the input and output must be closed by the delivered sticks. Otherwise unwanted
light can start an interrupt on the optical input circuit.

15 Remote control connector CN

External coupling devices are controlled via this remote control connector.

16 Fail detection FAIL 1 EUT control (TEST STOP)

Grounding this input will cause a complete stop of the running test procedure. (+15V to ground) The test must
be completely restarted.

Fail detection FAIL 2 EUT control (TEST PAUSE)

Grounding this input will cause a break for the running test procedure (+15V to ground).The test will be
continued when the input is no more connected to ground.

«
...
13
14
15
16
17
...
»

Содержание OCS 500 M6

















































































Отзывы:

Нет отзывов