Ametek Dycor CG1000-RTP Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 96

background image

Error Messages & Troubleshooting

|

6-5

Diagnostic Checks

Display the thermocouple millivolts and cell millivolts during trou-
bleshooting as a troubleshooting aid. You may need this information
if you need to contact the factory for assistance. Be sure to always
include your analyzer model and serial number when calling the fac-
tory for technical support.

Diagnostic checks are broken down as follows:

•  Wiring checks
•  Thermocouple checks
•  Calibration/aspirator setup checks
•  AC power checks
•  Furnace checks
•  Process pressure checks
•  Cell checks

Exercise care when working on the sensor. Turn off power, allow the
unit to cool and wear gloves.

Thermocouple Checks

Thermocouple Checks

To check the thermocouple you will

need a digital volt meter and a Type

K test meter.

-

First display the thermocouple

millivolts on the front panel

display. The display should

measure a positive voltage.

- If the display measures a nega-

tive voltage, reverse the wires

leading to pins TC+ and TC- on

the backplane board.

- To check the continuity of the

thermocouple, measure resistance

across pins TC+ and TC- on the

backplane board. The resistance

should be less than 5 Ohms.

Open Thermocouple

Disconnect power to the control unit and the sensor. Mea-

sure across terminals “TC+” and “TC-” on the backplane

board with an Ohm meter. If an open is measured, replace the

thermocouple.

Shorted/Failed Thermocouple

Check that the thermocouple leads are not shorted to chassis

ground by using an Ohm meter to measure between termi-

nal TC+ on the backplane board and chassis ground, and

between terminal TC- on the backplane board and chassis

ground. If shorted, replace the thermocouple.

- If this doesn’t solve the problem,

remove the thermocouple from

the analyzer and connect a Type

K test meter.

Using a thermometer, check the temperature of an environ-

ment. Place the thermocouple in this same environment and

check that the reading of the test meter measures the same

temperature as the thermometer. If the thermocouple measures

the temperature incorrectly (greater than 1% of expected tempera-

ture), replace the thermocouple

NOTE



«
...
67
68
69
70
71
...
»

Содержание Dycor CG1000-RTP

































































































Отзывы:

Нет отзывов

Похожие инструкции для Dycor CG1000-RTP

Бренд: E Instruments Страницы: 2

Surface Scatter 7 sc

Бренд: Hach Страницы: 6

Бренд: Hach Страницы: 118

Бренд: Hach Страницы: 388

Orbisphere 51 Series

Бренд: Hach Страницы: 118

ORBISPHERE 3650 Atex

Бренд: Hach Страницы: 51

Бренд: Hach Страницы: 72

POLYMETRON 8362

Бренд: Hach Страницы: 78

Pocket Colorimeter II

Бренд: HACH LANGE Страницы: 146

Бренд: Hach Страницы: 146

Бренд: Hach Страницы: 36

PHOSPHAX indoor sc

Бренд: Hach Страницы: 104

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 384

Бренд: Hach Страницы: 172

DIRIS Digiware D-40

Бренд: socomec Страницы: 58

Бренд: Solartron Mobrey Страницы: 34

Бренд: M&C Страницы: 18

Бренд: CONDTROL Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды