Ametek Dycor CG1000-RTP Скачать руководство пользователя страница 50

Страница: 50 / 96

4-16 | Dycor CG1000-RTP Oxygen Analyzer

Alarm Configure

Define whether alarms should trigger based on high oxygen, low oxygen,

or combined high/low flow condition.

Alarm 3 is set high or low oxygen or combined high/low flow. Alarm 4
is set to trigger high or low oxygen.

Configuring the alarms

1. From the

Alarm

menu, select

Alarm Configure

2. Define Alarm 3 as a high oxygen, low oxygen, or combined high/low

flow and Alarm 4 as high oxygen or low oxygen.

3. Press

Cancel

to exit this menu option.

To create two high oxygen alarms, define both Alarm 3 and Alarm 4 as
high oxygen alarms.

Relay Configure

All Series CG1000-RTP relays are Form A—normally open contacts. You
can use the software to set whether the alarms should close on an alarm
condition (energize) or open on an alarm condition (de-energize).

Configuring the relay

1. From the

Alarm

menu, select

Relay Configure

2. Select

De-energize on Alarm

Energize on Alarm

If you select

Energize on Alarm

, the following appears:

Relays are set to
ENERGIZE on Alarm

If you select

De-Energize on Alarm

, the following appears:

Relays are set to

DE-ENERGIZE on Alarm

NOTE



Содержание Dycor CG1000-RTP

































































































Результаты поиска

Содержание Dycor CG1000-RTP

Отзывы:

Похожие инструкции для Dycor CG1000-RTP

Бренды по названию

Популярные бренды

Ametek Dycor CG1000-RTP, Руководство пользователя

Результаты поиска

Содержание Dycor CG1000-RTP

Отзывы:

Похожие инструкции для Dycor CG1000-RTP

Бренды по названию

Популярные бренды