Ametek Dycor CG1000-RTP Скачать руководство пользователя страница 67

Страница: 67 / 96

Error Messages & Troubleshooting

6-3

Error Messages

Error messages on the control unit display indicate problems with the op-
eration of the analyzer. Identify the type of problem indicated by the error
message and go to “Diagnostic Checks” at the end of this chapter for help
on how to pinpoint the problem.

Always perform the easiest checks first. Only perform the more dif-
ficult checks if the easiest checks don’t locate the problem.

Cell Is Over Temp

The sensor temperature is 30°C or more over correct operating tem-

perature. The software shuts off the furnace until the temperature

returns to normal operating range.

When the temperature has returned to an acceptable range, the message clears. If there is a problem with the sensor

temperature control system, another error message will appear after this message.

Excessive Cal Error

The Primary Calibration has failed because it cannot correct the sen-

sor temperature to within the software’s allowable limits.

Possible reasons for failure are:

- Calibration gas setup problem

- Incorrect flow rates between calibration gases

- Failed pressure sensor

- Failed cell (primary calibration should be run at this time)

- Leak or plug in plumbing

- Cell lead wires polarity reversed

- Flow sensor not calibrated

- Wrong carrier gas selected

Memory is Corrupted

The control unit’s internal EEPROM memory has been corrupted or a

significantly new version of software has been installed in the control

unit. Under these conditions, the software will reprogram the EE-

PROM with factory defaults. Clear this message by setting or reading

any user-programmable value. This message will not clear by remov-

ing and then restoring power to the unit.

If you see this message, you should reset the analyzer to the values required for your application, including

Setup

Key,

Calibrate

Key,

Alarm

Key and

Analog Range

Key settings. In particular, be sure to re-select the carrier gas carrying

the sample (

Setup

key/

Carrier Gas

) and calibrate the flow sensor.

Span Gas Range

Error

Calibration span gas does not read within the software’s allowable

limits. This error causes calibration of the system to abort.

Possible reasons for failure are:

- Calibration gas setup problem

- Incorrect flow rates between calibration gases

- Calibration gas value incorrectly entered

- Failed cell (primary calibration should be run at this time)

- Leak or plug in plumbing

NOTE



Содержание Dycor CG1000-RTP

































































































Результаты поиска

Содержание Dycor CG1000-RTP

Отзывы:

Похожие инструкции для Dycor CG1000-RTP

Бренды по названию

Популярные бренды

Ametek Dycor CG1000-RTP, Руководство пользователя

Результаты поиска

Содержание Dycor CG1000-RTP

Отзывы:

Похожие инструкции для Dycor CG1000-RTP

Бренды по названию

Популярные бренды