Ametek Dycor CG1000-RTP Скачать руководство пользователя страница 29

Страница: 29 / 96

Installation & Start-Up

3-9

RS-232 Communications Connections

The CG1000-RTP communicates with other computers using RS-232 serial
communications protocol. The connections used for RS-232 communica-
tions are on connector J7 and labeled as follows (see Figure 3-1 for location
of J7 on back of CG1000-RTP).

dcd

Pin 1

Pin 2

Pin 3

dTR

Pin 4

gnd

Pin 5

dsR

Pin 6

RTs

Pin 7

cTs

Pin 8

n/A

Pin 9

Select 115/230 Volt Operation

To change the selected voltage:

• Disconnect the AC line power cord from the analyzer.

• Open the top cover of the power entry module using a small-blade

screwdriver.

• Select the voltage by rotating the fuse holder so the desired voltage

aligns with the window, then snap into place.

If you later want to switch the voltage source for the analyzer, you will
also need to change the fuses in the power entry module:

•

115 VAC - Fuse Rating: 2 amp, 250 VAC - Slow Blow

•

230 VAC - Fuse Rating: 1 amp, 250 VAC - Slow Blow

The fuse sizes are 1/4” x 1 1/4”. Do not use 5 x 20 mm fuses.

If the analyzer is a 230-Volt type, the power cord plug must be
changed to the proper type to match your country and/or electrical
code.

NOTE



Содержание Dycor CG1000-RTP

































































































Результаты поиска

Содержание Dycor CG1000-RTP

Отзывы:

Похожие инструкции для Dycor CG1000-RTP

Бренды по названию

Популярные бренды

Ametek Dycor CG1000-RTP, Руководство пользователя

Результаты поиска

Содержание Dycor CG1000-RTP

Отзывы:

Похожие инструкции для Dycor CG1000-RTP

Бренды по названию

Популярные бренды