Ametek Dycor CG1000-RTP Скачать руководство пользователя страница 40

Страница: 40 / 96

4-6 | Dycor CG1000-RTP Oxygen Analyzer

Upon completion of the primary calibration, the system notifies you
that a standard calibration is required by displaying a

Calibration Re-

quired

message. Oxygen readings on the display will not be accurate

until you perform a regular calibration.

A 15-minute recovery time follows the primary calibration to allow
the cell to stabilize. Wait an additional 45 minutes, then perform a
regular calibration.

Communication

Define RS-232 communications parameters between the CG1000-RTP and a

host device.

Baud Rate

Define the baud rate that the analyzer and the host comput

er use to communicate. choices are 300, 600, 1200, 2400,

4800, and 9600 baud.

Node Address

Define the physical address for the control unit (between 0

and 255) on a network so the host computer can identify the

control unit if using network communications.

Enable Serial

Temporarily disable cg1000-RTP serial communications.

Carrier Gas

Define which carrier gas is used to deliver the calibration gases to the analyzer

and calibrate the analyzer flow sensor to improve its accuracy.

You must select the proper carrier gas to ensure proper calibration of
the analyzer.

Define carrier gas

1. From the

Setup

key menu, select

Carrier Gas

2. Select the

Carrier Gas

sub-menu.

3. Select the carrier gas used to deliver gases to the analyzer. Choices are

nitrogen, carbon dioxide, argon, or helium. If measuring close to 100%
oxygen, we recommend that you select nitrogen as the carrier gas.

NOTE



See the “Serial Communica-

tions” appendix for complete

information on serial com-

munications.

NOTE



Содержание Dycor CG1000-RTP

































































































Результаты поиска

Содержание Dycor CG1000-RTP

Отзывы:

Похожие инструкции для Dycor CG1000-RTP

Бренды по названию

Популярные бренды

Ametek Dycor CG1000-RTP, Руководство пользователя

Результаты поиска

Содержание Dycor CG1000-RTP

Отзывы:

Похожие инструкции для Dycor CG1000-RTP

Бренды по названию

Популярные бренды