Ametek Dycor CG1000-RTP Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 96

background image

3-2 | Dycor CG1000-RTP Oxygen Analyzer

Mechanical Installation



Sample Gas

Requirements

sample gas/calibration gas set-up

PPM Measurement suggestions

Sensor

Ambient Temperature Range

-0 °c to 40 °c (32 °F to 104 °F)

Sample Flow Rate

150 cc/min recommended

Max Sample Flow Rate

200 cc/min

Max Sample Pressure Limit

3 Psig

Max Sample Inlet Temperature

700°c (160°F)

Locate the CG1000-RTP as close to sampling system as possible.



The accuracy of the oxygen readings are pressure- and flow-dependent.

Maintain the same

flow rate and

inlet pressure during both calibration

and normal operations. Keep the flow rate between 125 to 175 cc/min

to maintain accurate readings. To detect when the flow exceeds these

limits, Alarm 3 can be programmed to alarm on both the high and low

flow rate.

Figure 3-1 shows the sample inlet and outlet ports on the CG1000-RTP.
The sample gas should be clean and dry. If the sample contains any con-
densing moisture, the entire sample line should be heat-traced.

Be aware that combustibles in the sample can burn with available
oxygen to provide lower-than-expected oxygen levels, especially if
measuring oxygen in the low PPM ranges.

Keep the inlet pressure as low as possible to prevent damage to the cell or
cell O-ring seal. The sample gas inlet pressure into the CG1000-RTP must
be less than 3 PSIG.

Figure 3-1. Rear of CG1000-RTP analyzer.

NOTE



If the sample contains

particulates greater than 15

microns, install a filter on the

sample gas inlet.

«
...
20
21
22
23
24
...
»

Содержание Dycor CG1000-RTP

































































































Отзывы:

Нет отзывов

Похожие инструкции для Dycor CG1000-RTP

Бренд: Yamaha Страницы: 8

Бренд: Kawai Страницы: 66

Бренд: Hammond Organ Страницы: 25

Бренд: Hammond Organ Страницы: 87

Бренд: M-system Страницы: 16

Бренд: M-system Страницы: 25

Zetasizer Nano Series

Бренд: Malvern Страницы: 16

Бренд: Unior Страницы: 2

Бренд: Vaisala Страницы: 83

YPP-100 Light Piano

Бренд: Yamaha Страницы: 54

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 56

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 32

Бренд: ELGO Electronic Страницы: 24

OPERA CONTROL CENTER SERVER - V 3.5

Бренд: OPTICOM Страницы: 21

OPTIFLUX 4040 C Series

Бренд: KROHNE Страницы: 20

Бренд: Pyle Pro Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды